Connecting the Units Note: • When this unit is installed in a vehicle without ACC (accessory) position on the ignition switch, red cable must be wired to the terminal that can detect the operation of the ignition key. Otherwise, battery drain may result. ACC <ENGLISH> • Control signal is output through blue/white cable when this unit is powered on. Connect it to an external power amp’s system remote control or the vehicle’s auto-antenna relay control terminal (max. 300 mA, 12 V DC). If the vehicle is equipped with a glass antenna, connect it to the antenna booster power supply terminal. Never connect blue/white cable to external power amp’s power terminal. Also, never connect it to the power terminal of the auto antenna. Otherwise, battery drain or malfunction may result. IP-BUS connectors are color-coded. Be sure to connect connectors of the same color. Black cable is ground. This cable and other product’s ground cable (especially, high-current products such as power amp) must be wired separately. Otherwise, fire or malfunction may result if they are accidentally detached. Power cable connection AUX jack (3.5 ø) Note: Depending on the kind of vehicle, the function of 3* and 5* may be different. In this case, be sure to connect 2* to 5* and 4* to 3*. 1* 3* 2* This product 5* 4* Connect leads of the same color to each other. Use a mini plug cable to connect with auxiliary device. Antenna jack 15 cm 15 cm IP-BUS input (Blue) IP-BUS cable Multi-CD player (sold separately) Yellow/black If you use an equipment with Mute function, wire this lead to the Audio Mute lead on that equipment. If not, keep the Audio Mute lead free of any connections. Violet/white Of the two lead wires connected to the back lamp, connect the one in which the voltage changes when the gear shift is in the REVERSE (R) position. For details, refer to When connecting with a rear view camera. Blue/white Connect to system control terminal of the power amp (max. 300 mA 12 V DC). Hard-wired remote control adaptor can be connected (sold separately). 20 cm 1.5 m USB cable Connect to separately sold USB device. êìäéÇéÑëíÇé èé ìëíÄçéÇäÖ • O OF N F INSTALLATION MANUAL OF F O N STAR STAR DVH-P500UB ACC position • No ACC position • Use this unit in other than the following conditions could result in fire or malfunction. — Vehicles with a 12-volt battery and negative grounding. — Speakers with 50 W (output value) and 4 ohm to 8 ohm (impedance value). To prevent short-circuit, overheating or malfunction, be sure to follow the directions below. — Disconnect the negative terminal of the battery before installation. — Secure the wiring with cable clamps or adhesive tape. To protect the wiring, wrap adhesive tape around them where they lie against metal parts. — Place all cables away from moving parts, such as gear shift and seat rails. — Place all cables away from hot places, such as near the heater outlet. — Do not pass the yellow cable through a hole into the engine compartment to connect to a battery. — Cover any disconnected cable connectors with insulating tape. — Do not remove RCA caps if RCA cables are not used. — Do not shorten any cables. — Never cut the insulation of the power cable of this unit in order to share the power to other equipment. Current capacity of the cable is limited. — Use a fuse of the rating prescribed. — Never wire the speaker negative cable directly to ground. — Never band together multiple speaker’s negative cables. Printed in Thailand ç‡ÔÂ˜‡Ú‡ÌÓ ‚ í‡ËÎ‡Ì‰Â <CRD4326-A/N> RE <KMMNX> <07L00000> T T • • Cap (1*) Do not remove cap if this terminal is not in use. Yellow (3*) Back-up (or accessory) Fuse (10 A) Yellow (2*) Connect to the constant 12 V supply terminal. Red (5*) Accessory (or back-up) Red (4*) Connect to terminal controlled by ignition switch (12 V DC). Fuse resistor Black (chassis ground) Connect to a clean, paint-free metal location. Blue/white (6*) Blue/white (7*) Connect to auto-antenna relay control terminal (max. 300 mA 12 V DC). The pin position of the ISO connector will differ depends on the type of vehicle. Connect 6* and 7* when Pin 5 is an antenna control type. In another type of vehicle, never connect 6* and 7*. Note: In some vehicles, the ISO connector may be divided into two. In this case, be sure to connect to both connectors. When you connect the separately sold multi-channel processor (DEQ-P6600) to this unit, do not connect anything to the speaker leads and system remote control (blue/white). Speaker leads White: Front left + White/black: Front left ≠ Gray: Front right + Gray/black: Front right ≠ Green: Rear left + or subwoofer + Green/black: Rear left ≠ or subwoofer ≠ Violet: Rear right + or subwoofer + Violet/black: Rear right ≠ or subwoofer ≠ Notes: • Change the initial setting of this unit (refer to the Operation Manual). The subwoofer output of this unit is monaural. • When using a subwoofer of 70 W (2 Ω) , be sure to connect with Violet and Violet/black leads of this unit. Do not connect anything with Green and Green/black leads.
Вывести на печать