Click here to download the catalog as a PDF file.


Pioneer user manual - Page 3

Section Connections Connections 02 Important ! When installing this unit in a vehicle without an ACC (accessory) position on the ignition switch, failure to connect the red cable to the terminal that detects operation of the ignition key may result in battery drain. F — Never wire the negative speaker cable directly to ground. — Never band together negative cables of multiple speakers. O N ACC position No ACC position ! Use of this unit in conditions other than the following could result in fire or malfunction. — Vehicles with a 12-volt battery and negative grounding. — Speakers with 50 W (output value) and 4 W to 8 W (impedance value). ! To prevent a short-circuit, overheating or malfunction, be sure to follow the directions below. — Disconnect the negative terminal of the battery before installation. — Secure the wiring with cable clamps or adhesive tape. Wrap adhesive tape around wiring that comes into contact with metal parts to protect the wiring. — Place all cables away from moving parts, such as the shift lever and seat rails. — Place all cables away from hot places, such as near the heater outlet. — Do not connect the yellow cable to the battery by passing it through the hole to the engine compartment. — Cover any disconnected cable connectors with insulating tape. — Do not shorten any cables. — Never cut the insulation of the power cable of this unit in order to share the power with other devices. The current capacity of the cable is limited. — Use a fuse of the rating prescribed. ! When this unit is on, control signals are sent through the blue/white cable. Connect this cable to the system remote control of an external power amp or the vehicle’s auto-antenna relay control terminal (max. 300 mA 12 V DC). If the vehicle is equipped with a glass antenna, connect it to the antenna booster power supply terminal. ! Never connect the blue/white cable to the power terminal of an external power amp. Also, never connect it to the power terminal of the auto antenna. Doing so may result in battery drain or a malfunction. ! The black cable is ground. Ground cables for this unit and other equipment (especially, high-current products such as power amps) must be wired separately. If they are not, an accidental detachment may result in a fire or malfunction. 5 Fuse (10 A) 6 Power cord input 7 Wired remote input Hard-wired remote control adapter can be connected (sold separately). 8 Microphone input (DEH-X8500DAB and DEH-X8500BT only) 9 Microphone (DEH-X8500DAB and DEHX8500BT only) 4m a Rear output b Front output c Subwoofer output d USB cable 1.5 m ! Only for DEH-X8500DAB and DEH-X8500BT If connecting both USB1 (USB storage device1)/iPod1 (iPod connected using USB input1) and USB2 (USB storage device2)/iPod2 (iPod connected using USB input2) at the same time, use a Pioneer USB cable (CD-U50E) in addition to the regular Pioneer USB cable. Power cord English 3 4 2 5 6 1 OF 3 7 8 9 5 4 6 STAR T c a e d b This unit 9 3 2 1 d c 4 56 78 a b 1 USB port 1 2 USB port 2 (DEH-X8500DAB and DEHX8500BT only) 3 Antenna input 15 cm 4 DAB antenna input (DEH-X8500DAB only) To receive DAB signals, connect a DAB antenna (AN-DAB1) sold separately to the unit. 1 To power cord input 2 Depending on the kind of vehicle, the function of 3 and 5 may be different. In this case, be sure to connect 4 to 5 and 6 to 3. 3 Yellow Back-up (or accessory) 4 Yellow Connect to the constant 12 V supply terminal. 5 Red Accessory (or back-up) 6 Red Connect to terminal controlled by ignition switch (12 V DC). 7 Connect leads of the same color to each other. 8 Orange/white Connect to lighting switch terminal. 9 Black (chassis ground) En 3

Page 2 ... Page 4